![]() ![]() Seal the bolt with the metal washer and nut from the bottom of bolt.Place the smooth side of the bolt upward and rough side downward. Fix the bracket of monitor using bolts on the holes.Start with drilling the small holes and then progress to the bigger ones to avoid risk of errors.Drilling the holes require extra attention to protect the delicate fiberglass.Mark the points with the pencil to allow perfect drilling.Place the bracket of the monitor on the console where you want to mount the monitor.The question arises how to install the monitor. If you have adopted the right installation steps you should have known where to mount the monitor. This is the point where you have to deal with care. Place the plastic conduit along the path of the console around the wires.Set the transducer wires on the same way keeping in view the arrangement of cords of pontoon boat.It allows ease during installation process. Now, you can look at the inner arrangement of the cords. Moving from the console to the rear side of the pontoon, the siding is removed.This prevents the misplacement of screws. ![]() Fix the screws before moving on to the next one.Take the help from other end to prevent the rear end from falling down. Make sure not to remove the siding of pontoon on your own.When done with care, it is easy and causes no harm. This part seems difficult as it is a bit risky. Washer can be used during this part to deal with large size of the bolt. Use a drill machine to make two holes on the bottom bracket of the pontoon boat using the accurate measurements.Ĭare is necessary as tube can get punctured.įix the transducer setup of depth finder using the accessory items. If you read the instructions carefully, it can be an easier process. This will upgrade your courtesy lighting, give your boat a fresh look and allow you to do all the wiring for 2 upgrades on your pontoon boat at one time. While you’re working on this you might consider getting some marine LED lighting strips to add to your boat. Rubber and metal washers Plastic tubing to keep the wires safe and insulatedĮlectrical wires for providing power connections (if your pontoon boat doesn’t have a fuse box) Nut bolts that fits each other perfectly. To remain stress-free and get your installation completed in short time, make sure to buy all the required items.įollowing are the compulsory materials that I would recommend buying for depth finder installation process: Many customers don’t know that the kit of depth finder doesn’t contain all the materials needed for installation of depth finder. Step 4: Buy Extra Stuff Needed For Installation This understanding helps you to place the cables for the depth finder easily. The construction of boat is in such a way that the cords run throughout the boat.Īll the cords emerge from the deck hole and move back to the engine. The screen size with standard 5” is easy to mount.Īfter you are done in finding the right place, get off the boat and make sure that there is no interference between the wires of monitor and fish finder. The other thing to consider is the width of the screen. Step 3: Correct Placement Of Monitorįind the proper place for placing the monitor of depth finder. The optimal length of the wire for maximum number of pontoons is 20” (5.7meters). If the livewell pump is present, it is essential to keep it farther away from the wires to avoid signal distortion. Make sure to maintain optimum distance between the wires to prevent interference. Many pontoon boats are placed on the bottom or back of the pontoon.Ī wire is used to connect transducer with the monitor. The location of transducer varies from one boat to other. The information is then displayed on the monitor screen. Transducer sends and receives the waves and collects the data from the water depth. The technology of Sonar is used in the depth finders to make it function properly. Step 2: Find The Right Location For Transducer Make sure the complete kit of depth finder is of great quality and boost the performance of the fish finders. You can search the best fish finder for pontoon boats. The depth finder which matches your pontoon and its working criterion is the one you should look for. The preliminary step for the installation of depth finder is having the great depth finder. Step 1: Find The Best Depth Finder For Pontoon Boat Step 4: Buy Extra Stuff Needed For Installation.Step 2: Find The Right Location For Transducer.Step 1: Find The Best Depth Finder For Pontoon Boat.Procedure Of Installing A Depth Finder On A Pontoon Boat. ![]()
0 Comments
Leave a Reply. |